- Home
- Move Water
- Berkeley
- Berkeley Products
- Berkeley Jet Pumps
- Pentair Berkeley SL / SLJ Series Cast Iron Convertible Jet Pumps
Pentair Berkeley SL / SLJ Series Cast Iron Convertible Jet Pumps
Main Content Starts Here
Pentair Berkeley SL / SLJ Series Cast Iron Convertible Jet Pumps
The ProJet SL convertible jet pumps offer a proven cast iron self-priming design available in 1/2 thru 1-1/2 HP models. The ProJet SL convertible jets utilize Berkeley built-in regulators offering easier priming and better range of performance from a complete line of shallow well, 4" double pipe, 2" and 3" single pipe jet packages.
- Quality Cast Iron Construction: Pump Body is Rugged One-Piece Unit, Specially Treated to Resist Corrosion. Drain Port Provided for Easy Winterizing
- Precision Molded NORYL Impeller for Perfect Balance. Ultra Smooth for Highest Performance and Efficiency
- Precision Molded Diffuser Primes Faster, Handles More Air. Multi-Port, Precision-Molded Reinforced Polypropylene
- High Quality Pressure Switch With Adjustable Cut-In Setting. Fixed 20 PSI Differential
- Mechanical Shaft Seal With Precision Lapped Highly Polished Carbon-Ceramic Surfaces and Stainless Steel Construction
- Superior Insulations Materials on Motor Windings Protect Against Excessive Moisture and Contaminants .... Assures Prolonged Motor Life
- Balanced Rotor is Die Cast Under High Pressures for Uniform Performance and Greater Efficiency
- Shielded, Permanently Lubricated Ball Bearings, Extensively Tested to Ensure Extended Life and Smooth, Quiet Operation
- 416 Stainless Steel Pump and Motor Shaft for Maximum Corrosion Resistance. One Piece Threaded Shaft for Positive Impeller Drive and Alignment
- Dustproof Motor Canopy Protects All Electrical Components From Dirt, Dust and Insects. Ventilating Air Cannot Contaminate Vital Switching Components ... The Most Common Cause of Motor Failure
Specifications
Item # | Primary Product Attributes | Horsepower | Voltage | BODY and SEAL PLATE | Impeller | DIFFUSER | Shaft | BASE | MAX LIQUID TEMP | MAX INLET PRESSURE | PRESSURE SWITCH PRE-SET | PORT SIZES | SUCTION PORTS |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
17914 | Available in 1/2 thru 1-1/2 HP | 115 / 230 volts, 60 Hz | Close-Grained Cast Iron | High Strength NORYL® | Reinforced Polypropylene w/ Brass Wear Ring | One-Piece Threaded 416 Stainless Steel | 10-gauge Steel | 140 degrees F (60 degrees C) | 50 PSI | 30 - 50 PSI | Suction: 1-1/4" / Drive: 1" / Discharge: 1" | Suction-Over-Drive |
Item # | Primary Product Attributes | Horsepower | Voltage | BODY and SEAL PLATE | Impeller | DIFFUSER | Shaft | BASE | MAX LIQUID TEMP | MAX INLET PRESSURE | PRESSURE SWITCH PRE-SET | PORT SIZES | SUCTION PORTS |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
17914 | Available in 1/2 thru 1-1/2 HP | 115 / 230 volts, 60 Hz | Close-Grained Cast Iron | High Strength NORYL® | Reinforced Polypropylene w/ Brass Wear Ring | One-Piece Threaded 416 Stainless Steel | 10-gauge Steel | 140 degrees F (60 degrees C) | 50 PSI | 30 - 50 PSI | Suction: 1-1/4" / Drive: 1" / Discharge: 1" | Suction-Over-Drive |